
GO Faster Go Further
Established since 2001
Secure Supplies Group
9XD Power Supply Card Stanley Meyer
Power supply card ,the Stanley Meyer 9xd is just power for the circuit.
But is is rather Special to us all, it has ability to gatheer eletrcon from ambient sources like EEC eelectron extraction card or recievers or earth batteries. It can gather voltrage control it and regulate it to 8XA ,9XB ,,9XA VIC, LED PULSER AND GAS PROCESSOR CARDS.


This circuit is good to scavange ambient power and send it to a charge controller and battery bank also , Can be used with the electron extraction and to power Stanley Meyer Devices.

power supply regulation
9XD
step down transformer.....full wave rectifier.......smoothing capacitors....voltage regulators ....smoothing caps
120 volts from the wall AC
the step down transformer turns the 120 volts AC into 14 to 36 volts AC
the full wave bridged rectifier turns that into pulsed DC
the smoothing capacitor removes the pulsed ripple and makes a clean DC
the regulator maintains the output voltage. 7805 is 5 volts and 7812 is 12 volt. extra voltage is given off as heat.
the other cap is then used to smooth the ripple from the regulator
out goes a clean voltage to the pulse circuit
AC power
http://en.wikipedia.org/wiki/Alternating_current
transformer
http://en.wikipedia.org/wiki/Transformer
diode bridge
http://en.wikipedia.org/wiki/Diode_bridge
smoothing capacitor
http://en.wikipedia.org/wiki/Reservoir_capacitor
78xx series voltage regulators
http://en.wikipedia.org/wiki/78xx
DC power
http://en.wikipedia.org/wiki/Direct_current

The 9XD is Shown here inside a Voltage Intensifier Box , that was used for patent application process by Stanley Meyer . The Box would Run on Main Power and Turn 110/220 to DC 12v and 5 v.
Stanley Meyer use a Variac inside this Box pulsed with 8XA/9XA 555 and frequency ship set array which was inverted aprox 5 khz.
there is a SCR Daughter board type switch to switch in the high dc to the pwm signal.
this allow a gated signal and a high voltage ionization to occur at same time ( gated) polarizing the water and ionizing it to break bonds of h and o with little or no amps
A DBD barrier type effect is made on the out cathode tube which has a larger surface are than the inner tube.
This High Voltage Dc out put between 400 to 600 v at less than 4 amp then went into a bifilar wound e core 2000 perm which than went through a blocking diode to wfc water cell wet cell tube array no electrolyte.
step down transformer.....full wave rectifier.......smoothing capacitors....voltage regulators ....smoothing caps
120 volts from the wall AC
the step down transformer turns the 120 volts AC into 14 to 36 volts AC
the full wave bridged rectifier turns that into pulsed DC
the smoothing capacitor removes the pulsed ripple and makes a clean DC
the regulator maintains the output voltage. 7805 is 5 volts and 7812 is 12 volt. extra voltage is given off as heat.
the other cap is then used to smooth the ripple from the regulator
out goes a clean voltage to the pulse circuit
AC power
http://en.wikipedia.org/wiki/Alternating_current
transformer
http://en.wikipedia.org/wiki/Transformer
diode bridge
http://en.wikipedia.org/wiki/Diode_bridge
smoothing capacitor
http://en.wikipedia.org/wiki/Reservoir_capacitor
78xx series voltage regulators
http://en.wikipedia.org/wiki/78xx
DC power
http://en.wikipedia.org/wiki/Direct_current

this is a simple power regulater
input of 14 volts......as high as 37 volts......
is regulated down to 12 volts and 5 volts
easy for a biginer to assemble with your kids
most circuits are 12 volt or 5 volts, this unit regulates your voltage so the circuit will not melt from to much voltage
the regulators have automatic shut down if over heated or over amped
regulated voltage is 12 volts and 5 volts from AC 14 or more volts
or DC 14 or more volts
these are 1.5 amp chips.....double them for 3 amps
common use is powering circuits you are prototyping or even senstive electronics in your car
you can power your sensitive PWM main board,
mosfet switches for HHO would not go through this circuit
but this circuit would
protect the PWM main board

